Cisco CATALYST CW9163E-E AP(W6E TRI-BAND)

●  C9117AXI-x: Cisco Catalyst 9117

Cisco Catalyst 9117AXI Access Point: Indoor environments, with internal antennas, with embedded wireless controller

●  C9117AXI-EWC-x: Cisco Catalyst 9117

Regulatory domains: (x = regulatory domain)

Customers are responsible for verifying approval for use in their individual countries. To verify approval and to identify the regulatory domain that corresponds to a particular country, visit https://www.cisco.com/go/aironet/compliance.

Not all regulatory domains have been approved. As they are approved, the part numbers will be available on the Global Price List.

Cisco Wireless LAN Services

●  AS-WLAN-CNSLT: Cisco Wireless LAN Network Planning and Design Service

●  AS-WLAN-CNSLT: Cisco Wireless LAN 802.11n Migration Service

●  AS-WLAN-CNSLT: Cisco Wireless LAN Performance and Security Assessment Service

●  Cisco IOS XE Software Release 16.11 or later

●  Cisco 3500, 5520, and 8540 Series Wireless Controllers, and Cisco Virtual Wireless Controller

●  4×4 MIMO with four spatial streams for 2.4-GHz band

●  Maximal Ratio Combining (MRC)

●  20- and 40-MHz channels

●  PHY data rates up to 600 Mbps (40 MHz with 5 GHz)

●  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)

●  Cyclic Shift Diversity (CSD) support

●  MRC

●  802.11ac beamforming

●  20-, 40-, 80, and 160-MHz channels

●  PHY data rates up to 3.5 Gbps at 5 GHz

●  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)

●  CSD support

●  160 MHz support only on 4-spatial stream

●  4×4 MIMO with four spatial streams for 2.4-GHz band

●  Downlink OFDMA

●  TWT

●  MRC

●  802.11ax beamforming

●  20-, 40-, 80, and 160-MHz channels

●  PHY data rates up to 5 Gbps at 5 GHz

●  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)

●  CSD support

●  5 GHz, peak gain 6 dBi, internal antenna, omnidirectional in azimuth

●  Management console port (RJ-45)

●  USB 2.0 with up to 4.5W (enabled via future software)

●  Access point (without mounting bracket): 8.70 x 8.70 x 2.19 in. (22 x 22 x 5.56 cm)

●  Cisco power injector, AIR-PWRINJ6=

●  802.3af PoE

●  Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af)

Note: When 802.3af PoE is the source of power, both 2.4-GHz and 5-GHz radios will be reduced to 2×2 and Ethernet downgraded to 2.5 Gbps; in addition, the USB port will be off.

UPOE+, Cisco

UPOE

Note: Power required at the Power Source Equipment (PSE) will depend on the cable length and other environmental issues

●  Nonoperating (storage) altitude test: 25˚C, 15,000 ft.

●  Operating temperature: 32° to 122°F (0° to 50°C)

●  Operating humidity: 10% to 90% (noncondensing)

●  Operating altitude test: 40˚C, 9843 ft.

●  1024 MB flash

●  23 dBm (200 mW)

●  -6 dBm (0.25 mW)

●  26 dBm (400 mW)

●  -4 dBm (0.4 mW)

For information about Regulatory Domain support, refer to the Cisco Regulatory Domain White Paper